Log in to your TripLog web account, click “Expenses” under the QuickBooks tab on the menu bar, then filter trips by date range, activity and/or driver. Upload trips to QuickBooks as mileage reimbursement Expenses All done! Your TripLog is now connected with your QuickBooks account! Continue to your Corresponding Upload Option to setup Quickbooks On the pop up, please scroll down and press ‘Connect’.Ĥ. After verifying your account, you will be asked to authorize the connection between QuickBooks and TripLog. Please follow the prompts to verify your account.ģ. After signing in to QuickBooks Online, you will be prompted to verify your account using a code that will be sent to your phone or email. Please enter in your QuickBooksOnline / Intuit credentials to verify the connection with QuickBooks, then press ‘Sign In’. Then on top right of the section click “Connect to QuickBooks” button.Ģ. please log in to TripLog web dashboard and navigate to QuickBooks page from the top menu bar. To connect to QuickBooks Online, please follow these instructions:ġ. Using the TripLog web dashboard, you can connect and upload data to Intuit QuickBooks Online. Or, if you charge your clients for mileage, you would need to upload as Invoices. If you have employees and reimburse them for business use of their personal vehicles, you will need to upload TripLog data to QuickBooks as Expenses or Bills. You will still need to keep TripLog reports as supporting documents for this record. Instead, you would only need to run TripLog reports for the year and copy a few numbers to TurboTax, or an equivalent tax software, or give the reports to your tax preparer. In this case, you do not need to upload mileage to QuickBooks. If you don’t have an employee other than yourself, you probably just need to claim mileage deduction on your personal tax return. Uploading Mileage and Expenses as INVOICESĭo I need to upload mileage to QuickBooks? Uploading Mileage and Expenses as EXPENSES In order to re-enter normal operational model, simply remove and replace power to the device.Setting Up the QuickBooks Online Integration Select the DFU button to reboot the beacon into Direct Firmware Update mode.Ĭontact Radius Networks support for information on the procedure for firmware update or replacement. In order to re-enter configurable mode for a RadBeacon X2, remove the front cover and switch the beacon power switch to OFF and back to ON.Ī beacon set in configurable mode will be configurable for up to 30 minutes or until you lock the device again. In order to re-enter configurable mode for a RadBeacon Tag, remove the front cover and press the configuration push button switch near the coin cell battery. In order to re-enter configurable mode for a RadBeacon USB, remove and restore power to the device. The Lock feature is a security precaution to limit the possibility of third party manipulation of your beacons once they have been installed and configured. Select the Lock button to submit a valid PIN to prevent connections from remote Bluetooth 4.0 devices to the beacon configuration service. Submit a valid PIN to reset the settings for your beacon to factory defaults. Select the Reset button to reset the device to the original factory settings. ![]() Select the Update PIN button to submit a new and existing PIN to update the PIN for your beacon. Advertised Organizational Identifier Ĭhange any of the modifiable settings and select the Apply button to submit a valid PIN to update the settings for this beacon. Select any RadBeacon in the table to view it's detailed settings. Each beacon discovered is displayed with the following summary details Scan for nearby configurable RadBeacons by pressing the Start Scanning button. Once discovered, you can display each beacon's operating settings and make modifications to those settings. With the RadBeacon app you can scan for nearby configurable Radius Networks beacons. The RadBeacon app from Radius Networks requires a Macintosh computer running OS X 10.9 or higher and equipped with Bluetooth 4.0 capabilities. ![]() The RadBeacon™ app is the configuration utility for RadBeacon proximity beacons from Radius Networks that support Apple's iBeacon™ proximity services as well as other emerging proximity services.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |